Serial ports in equipment made by Sun Microsystems, Inc. (SUNW) ////////////////////////////////////////////////////////////////////////////// See also "Discussion of UNIX and LINUX terminal use". ////////////////////////////////////////////////////////////////////////////// Newsgroups: comp.unix.solaris NNTP-Posting-Host: 192.18.43.249 NNTP-Posting-Date: Thu, 17 Aug 2006 14:10:26 -0500 References: Message-ID: Organization: Sun Microsystems Date: 17 Aug 2006 15:12:11 -0400 From: James Carlson Subject: Re: serial ports not working "jmiklo" writes: > > I stumbled across 2 Sun 240 servers. > But it seems that serial ports are not working (I used port serial mgmt). > > I tried regular "cisco" console cable which I always use for accessing > Suns (9600 8N1). There is Net mgmt port, but I don't know how (if at all) > is configured. > > Have any idea how to start using those servers ? (to install new os) ? > If serial port is burned, is it necessary to replace whole motherboard, > or simple serial circuit can be replaced ? The last I looked (and it was a while ago), the serial pinout for a Cisco was different from the V240. I believe the control lines are interchanged. The V240 pinout should be: 1 - RTS 2 - DTR 3 - TxD 4 - GND 5 - GND 6 - RxD 7 - DSR 8 - CTS You may want to check that your console cable is wired appropriately, and search the web for alternatives. -- James Carlson, KISS Network Sun Microsystems / 1 Network Drive 71.232W Vox +1 781 442 2084 MS UBUR02-212 / Burlington MA 01803-2757 42.496N Fax +1 781 442 1677 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Newsgroups: comp.unix.solaris NNTP-Posting-Host: 89-172-28-125.adsl.net.t-com.hr NNTP-Posting-Date: Thu, 17 Aug 2006 19:27:00 +0000 (UTC) References: Message-ID: Date: Thu, 17 Aug 2006 21:26:54 +0200 From: jmiklo Subject: Re: serial ports not working "James Carlson" wrote in message news:xoav8xln89dg.fsf@sun.com... > > The last I looked (and it was a while ago), the serial pinout for a > Cisco was different from the V240. I believe the control lines are > interchanged.... > You may want to check that your console cable is wired appropriately, > and search the web for alternatives. Actually, I never bothered to check because it always worked with cisco console cable ... all kind of Sun servers I came to work with. In this rack I can connect to V120, but can't connect to V240. I believe difference is that cisco utp cable is already rolled but uses straight thru 9pin-to-rj45 connector. Sun uses straight utp cable but connector changes rx to tx pins. In the end it is pretty much the same, as long as you don't intermix cables and connectors from different vendors. I am pretty sure that problem is serial port, so I am trying to find solution (if any exists) to manage those servers. On V240 there is Rj45 serial interface, but above that there is also standard 9pin serial connector. I tried both and none worked. Is this same circuitry (i.e. serial 0) with 2 different inputs, or 2 separate serial ports (like ser0 and ser1) ? It is strange that none of those is working. thanks, jmiklo ////////////////////////////////////////////////////////////////////////////// Newsgroups: comp.unix.solaris NNTP-Posting-Host: deneb.cc.umanitoba.ca NNTP-Posting-Date: Mon, 8 Jan 2007 22:41:26 +0000 (UTC) References: <1168279498.634359.194800@38g2000cwa.googlegroups.com> <20070108133159.166e2850@oscar-sled.home.lan> <1168285352.423286.291970@51g2000cwl.googlegroups.com> <1168288960.255820.234320@q40g2000cwq.googlegroups.com> Message-ID: Organization: The University of Manitoba Date: Mon, 8 Jan 2007 22:41:26 +0000 (UTC) From: Gary Mills Subject: Re: Sunfire v210 serial console... configuration >Gary Mills wrote: >> In <1168285352.423286.291970@51g2000cwl.googlegroups.com> "forrie@gmail.com" > writes: >> >> >I see only a "net mgmt" port, and then the RJ45 and standard serial >> >ports... no LOM. Unless I'm mistaken about something. >> >> The RJ45 is also a management port, serial in this case. It's >> connected to the console by default, but you can escape from that >> to the ALOM. >> >> >The impression I got from the Sun docs was that LOM modifcation or >> >whatever requires the system brought down, which I can't do (production >> >system). I would "think" that the console is, by default, set to the >> >serial port. The eeprom settings seem to suggest that, but perhaps the >> >SAF has since been modified and ttymon isn't listening. I'm not sure >> >> You must be looking at RSC documentation. ALOM is completely >> different. No, the serial port is not the console. You don't need to >> change any eeprom settings. The ALOM can be used and configured >> without affecting the running system. >> >> -- >> -Gary Mills- -Unix Support- -U of M Academic Computing and Networking- In <1168288960.255820.234320@q40g2000cwq.googlegroups.com> "forrie@gmail.com" writes: >I just tried hooking up the RJ45 to the Serial *and* Net Mgmt ports, >with no luck. I'm pretty sure the COMMs parameters on the Wyse are >correct. The network management port is Ethernet. The serial management port is serial, using the Cisco cable format. If you have a cable that works on a Cisco router, it will work on the V210/V240. -- -Gary Mills- -Unix Support- -U of M Academic Computing and Networking- ////////////////////////////////////////////////////////////////////////////// Newsgroups: comp.sys.sun.hardware NNTP-Posting-Host: 62.254.246.40 NNTP-Posting-Date: Tue, 7 Nov 2006 09:14:22 +0000 (UTC) References: <1162395298.623789.241400@m7g2000cwm.googlegroups.com> <1162832587.987264.124700@b28g2000cwb.googlegroups.com> Message-ID: <1162890857.894379.184400@k70g2000cwa.googlegroups.com> Date: 7 Nov 2006 01:14:17 -0800 From: "BertieBigBollox@gmail.com" Subject: Re: LOM port on a Sunfire V100 On Nov 6, 5:03 pm, Patrick wrote: > > BertieBigBol...@gmail.com wrote: > > > > How do I connect to this from another PC? > > > > What sort of cable do I need? Network cable or crossover? > > > > I've got serial 9pin convertor which I can plug into serial port of PC. > > Tried using hyperterm on COM1 but no joy.... > > > > Am I missing something?The cable should be a crossover, and your settings > > should be 8-N-1, > > > 9600 should work fine. If you have other machines around, test on > those so you can determine if your setup works with other boxes. I > always forget how flow control needs to be set, but try them and save > your config when it works :) > > patrick Crossover? I always get confused - is this 'normal' RJ45 network lead? .............................................................................. Newsgroups: comp.sys.sun.hardware, comp.sys.sun.misc, comp.sys.sun.admin NNTP-Posting-Host: 220.233.163.88 NNTP-Posting-Date: Tue, 7 Nov 2006 10:27:04 +0000 (UTC) References: <1162395298.623789.241400@m7g2000cwm.googlegroups.com> <1162832587.987264.124700@b28g2000cwb.googlegroups.com> Message-ID: <1162895217.973260.10080@m73g2000cwd.googlegroups.com> Date: 7 Nov 2006 02:26:58 -0800 From: David Wilson Subject: Re: LOM port on a Sunfire V100 > BertieBigBollox@gmail.com wrote: > > > > How do I connect to this from another PC? > > > > What sort of cable do I need? Network cable or crossover? > > > > I've got serial 9pin convertor which I can plug into serial port of PC. > > Tried using hyperterm on COM1 but no joy.... If you have the DE-9F to RJ-45 adapter that Sun supplies (530-3100-xx) you just use a standard straight through network cable. If you need the pinouts to make one of these, I have them at work. Hyperterminal works fine for me in this application. ////////////////////////////////////////////////////////////////////////////// Newsgroups: comp.sys.sun.hardware NNTP-Posting-Host: p-832.newsdawg.com References: <444f8328$0$10672$afc38c87@news.optusnet.com.au> <2rO3g.64044$F_3.55651@newssvr29.news.prodigy.net> <4450023e$0$25525$afc38c87@news.optusnet.com.au> Message-ID: Organization: D & D Data, Vienna, VA Date: 29 Apr 2006 05:08:55 GMT From: DoN. Nichols Subject: Re: Ultra 1 uses a funky serial port pinout? According to Michael Brown : > Darren Dunham wrote: > > Michael Brown wrote: > >> > >> 2. So, the alternative was to use the serial port. This is where > >> things get odd ... I can *send* commands fine to the U1. However, > >> nothing ever gets sent back. > > > > So you're typing blind and it seems to work? > > Yup. Same thing happens on both ports (A and B), which is what makes me > suspect some sort of incompatibility thing is going on. Almost like the Sun > doesn't recognise the handshaking and thinks that the other computer isn't > ready. It's strange that it works fine on the U2 though. It sounds as though you need to change some EEPROM settings, or to force some handshake pins true. Take a look at the following entries (from an Ultra-1 which I have): ====================================================================== ttyb-rts-dtr-off=false ttyb-ignore-cd=true ttya-rts-dtr-off=false ttya-ignore-cd=true ttyb-mode=9600,8,n,1,- ttya-mode=9600,8,n,1,- ====================================================================== I think that you need to set your ttya-ignore-cd to true, and perhaps ttya-rts-dtr-off to true as well, so it will do no handshaking. This may mean that it will overrun a slow terminal if there is a lot to display, but you should at least get things done. On earlier systems, it was often necessary to hardwire the CD and DTR pins true -- or at least one of them. Nothing that I am currently running, not even the ancient LX, is old enough to lack those EEPROM options. With the ignore-cd setting false, it won't send anything to your terminal until it sees the CD pin true. (It thinks that it is talking to a modem, and wants the CD to tell it that the supposed modem is connected to something at the other end. You should be able to set these using the eeprom command (at least from a booted Sun OS, or from OpenBSD (that I know for sure), or from the OPENboot level, using the printenv and setenv commands. Good luck DoN. -- Email: | Voice (all times): (703) 938-4564 (too) near Washington D.C. | http://www.d-and-d.com/dnichols/DoN.html --- Black Holes are where God is dividing by zero --- .............................................................................. Newsgroups: comp.sys.sun.hardware NNTP-Posting-Host: 66.160.54.164 NNTP-Posting-Date: Sat, 29 Apr 2006 20:15:06 CDT References: <444f8328$0$10672$afc38c87@news.optusnet.com.au> <4b9ui7F10hhu1U1@individual.net> Message-ID: Date: Sat, 29 Apr 2006 21:14:58 -0400 From: Trinean Subject: Re: Ultra 1 uses a funky serial port pinout? > >Could it be that the Ultra 1 is set to use RS422? > > > > There is no such setting on the Ultra 1. Sure there is, or rather RS423. In fact RS423 is the default! According to the jumper chart J2104 and J2105 on the system board controls whether it is RS232 or RS423. Trinean ////////////////////////////////////////////////////////////////////////////// Newsgroups: comp.unix.solaris,comp.sys.sun.admin,comp.unix.admin Path: news.utk.edu!newsfeed.utk.edu!news-hog.berkeley.edu!ucberkeley! 128.135.12.170.MISMATCH!news.uchicago.edu!logbridge.uoregon.edu !hammer.uoregon.edu!news.glorb.com!news-out.octanews.net !indigo.octanews.net!auth.beige.octanews.com.POSTED!not-for-mail NNTP-Posting-Date: 28 Feb 2006 17:08:43 CST References: <1141166986.411659.131780@e56g2000cwe.googlegroups.com> Message-ID: <4404d7fb$0$87627$892e0abb@auth.newsreader.octanews.com> Organization: Octanews Date: 28 Feb 2006 23:08:43 GMT From: Doug McIntyre Subject: Re: When to use a null model cable or adapter? "Joe D." writes: > > I will need; particularly with regard to 'null modem' cabling. There's usually a DCE and a DTE. If you have two DCE's, you need a null modem in the middle to make one end look like a DTE by flipping transmit and receive, and whatever handshaking lines you are using. Thus, if you have a computer going to a computer, you'll need a null modem. > From my reading thus far, I understand that I will want to connect up > to the Serial A port to ensure that I get POST diags and other boot > messages at boot time and for maintenance. Does the connection to the > Serial port A ALWAYS need to be a null-modem connection, or does it > vary from server to server, and if so, does anyone know a link to a > quick summary of which Sun servers need what? I've been downloading > user and field service guides from Sun, but it would be nice to have > this in a concise tabular format. No, its pretty consistant, you pretty much need a null-modem everytime. Unless of course, you have a cable already wired as a null-modem. Some devices (just like in Ethernet) try to trick you out by making themselves look like DTEs instead of DCEs, and then you need a null modem on the end of your null modem cable if that is what you are using. FWIW: Sun followed along with the industry to make serial cables on RJ45 consistant to the Cisco standard. One nice feature of the Cisco layout is that if you roll the cable (ie. pin 1 to 8) and plug it in that way, you have a null modem. Very convenient. > Also, can anyone recommend any particular manufacturer of terminal > servers or switches, or whatever that would meet my needs? I'm looking > for capacity of 20 - 25 servers, with the ability for local access > (terminal in the actual computer room) and remote access to the switch, > where I could then select whichever server's port I needed. Sure, what's your budget? Cyclades makes some nice units. You'd probably be able to find 4-5 without really looking too hard. > Are there adapters available that turn a regular ether cable into a > null modem cable (say, a two piece connector set; one in Serial A, > the other on the Terminal serverport , and they're wired such that > all you need do is connect them with an ether?). It's better to use flat cable instead of twisted pair, but yes, there are adaptor modules you can buy. Since there aren't many consistant standards (or, perhaps too many standards that nobody followed one until recently), they all come unwired, and you are expected to wire them to whatever standard you want to use. Or, buy serial cables from your term server vendor at their higher price. The canonical page to refer to is at.. http://www.sunhelp.org/unix-serial-port-resources/ ////////////////////////////////////////////////////////////////////////////// Newsgroups: comp.unix.solaris NNTP-Posting-Host: 209.17.184.164 NNTP-Posting-Date: Fri, 6 Oct 2006 19:49:28 +0000 (UTC) References: <1160162503.436510.178140@i42g2000cwa.googlegroups.com> Message-ID: <1160164162.765433.174180@b28g2000cwb.googlegroups.com> Date: 6 Oct 2006 12:49:22 -0700 From: gerryt Subject: Re: ultra 10 serial serial port shea.martin@gmail.com wrote: > > Darren Dunham wrote: > > Odd. Normally you just leave it at the default of kbd/screen and then > > boot without a keyboard. It will automatically pop over to ttya. > > I think the cable I had was a DB9, and ttya is a DB25, so I had to > manually set it to ttyb. I believe when you manually set it, just > rebooting won't set it back to screen. You mean as in eeprom? Any change you make is permanent. > > If you mean in a windows machine to connect to the sun, then no. If > > it's a serial port it should work, but I don't have any > > recommendations. There's a lot of USB to serial converters as well, > > with different levels of success. hmm - I'm about to buy one today - wish me luck : / > I need the serial adaptor ror my PC laptop. I don't have access to a > WYSE term anymore, and I don't want to lug my desktop pc over there. > The reason I ask this question is that I have heard about PCMCIA and > USB serial port adapters not working with Palm Pilots, so I figured > there must be some non standard makes floating around out there. > Most local shops likely won't carry one, so that leaves eBay. No, it doesn't. There's all kinds of online stores. I've used DirectDial, for example. > eBay's turn around is slow, so I want to make sure I get the right one. Well if mine works out, I'll let you know. AFAICT* the USB - serial dongles are DB9. So an appropriate cable and DB25 adaptor are still a requirements.. [* "As far as I can tell"] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Newsgroups: comp.unix.solaris NNTP-Posting-Host: 209.17.184.164 NNTP-Posting-Date: Sat, 7 Oct 2006 18:25:33 +0000 (UTC) References: <1160162503.436510.178140@i42g2000cwa.googlegroups.com> <1160164162.765433.174180@b28g2000cwb.googlegroups.com> <1160166472.521323.248280@i3g2000cwc.googlegroups.com> <1160184996.434566.97520@c28g2000cwb.googlegroups.com> Message-ID: <1160245529.090749.70220@k70g2000cwa.googlegroups.com> Date: 7 Oct 2006 11:25:29 -0700 From: gerryt Subject: Re: ultra 10 serial serial port gerryt wrote: > > shea.martin@gmail.com wrote: > > gerryt wrote: > > > are DB9. So an appropriate cable and DB25 adaptor are still a > > > requirements.. > > So null modem cable not serial cable right? > In a manner of speaking. There is a site > http://www.obsolyte.com/sunFAQ/serial > which looks like a good starter. To follow up - I purchased an ATEN USB-serial converter part number UC232A-B yesterday for $16.28 CDN. ATEN stuff is fairly common this neck of the woods, so mail order shouldn't be too difficult, if local stores in your area don't carry this brand. I used a Cisco UTP-DB25 adapter, a straight CAT5 Ether cable to a generic UTP-DB9 adapter. I say generic, as I didn't change the pins around at all. Getting a Cisco DB25 adapter might be problematic?? If you have a breakout device of any kind you should see Sun side: 2 RTS and DTR lit up laptop side: pin 3, DTS and QM lit up. I downloaded TeraTerm from ayera.com after installing the ATEN driver on my Media Edition laptop (argh) .. HyperTerm didnt seem to have Break option so I scrapped it straight away. Strange, as I have seen some HyperTerm with a break option.. In my case the com port came up as COM4 so I set TeraTerm up at 9600 baud the rest I left as is. Works perfectly. This is good, as a straight cable is easier to come by, than some cross-wired contraption.. I mean if the one I carry around from site to site isnt QUITE long enough.. Good luck reviving your Ultra 10 ////////////////////////////////////////////////////////////////////////////// Newsgroups: comp.unix.solaris NNTP-Posting-Date: 12 Apr 2007 14:52:17 CDT References: <1176325483.693128.320220@w1g2000hsg.googlegroups.com> <461d5df8$0$36739$892e0abb@auth.newsreader.octanews.com> Message-ID: <461e8df1$0$36698$892e0abb@auth.newsreader.octanews.com> Date: 12 Apr 2007 19:52:17 GMT From: Doug McIntyre Subject: Re: USB serial dongle (wasRe: Does one have to buy any special equipment for the V125?) Liam Greenwood writes: > > On 11 Apr 2007 22:15:20 GMT, Doug McIntyre wrote: >> >> On the Mac, you'll need a USB to Serial dongle to do the initial setup >> to get at least an IP address/gateway/root password/user account setup >> on the box before it'll talk on the Network. >Does anyone have a recommendation for a USB serial dongle that works on the >Mac for connecting to Sun boxes? I have an old Thinkpad that I boot off CD >(dead HD) for this purpose at the moment, and would like to not have to >depend on it. Keyspan work great. Driver support is great (as opposed to others like the Prolific chipset based ones). Since I work on a bunch of routers as well as machines, I have the 4-port Keyspan unit as well as single dongles for my powerbook. Then Kermit [for software], although thats a personal preference, although I see it echoed by at least one other here... ////////////////////////////////////////////////////////////////////////////// Newsgroups: comp.unix.solaris NNTP-Posting-Host: 140.158.244.81 NNTP-Posting-Date: Mon, 8 Jan 2007 22:29:22 +0000 (UTC) References: <1168279498.634359.194800@38g2000cwa.googlegroups.com> Message-ID: <1168295355.745861.318240@51g2000cwl.googlegroups.com> Date: 8 Jan 2007 14:29:15 -0800 From: victorfeng1973@yahoo.com Subject: Re: Sunfire v210 serial console... configuration forrie@gmail.com wrote: > > I've a SunFire v210 in our lab for which we require a console > connection (no video console). I see the RJ45 and DB9 connections on > the back. Tried hooking up a Wyse terminal, 9600,8,N,1, and wasn't > able to get a prompt. "eeprom" shows: > > ttyb-rts-dtr-off=false > ttyb-ignore-cd=true > ttya-rts-dtr-off=false > ttya-ignore-cd=true > ttyb-mode=9600,8,n,1,- > ttya-mode=9600,8,n,1,- > output-device=ttya > input-device=ttya Your parameters are fine. We have v240 which is very close to yours. I use RJ45/DB9 in SERIAL MGT. I used both HyperTerminal (COM1 port properties (Restore Defaults)) and TeraTerm. They all work fine. What is your ALOM version? -- /usr/platform/`uname -i`/sbin/scadm version? Victor .............................................................................. Newsgroups: comp.unix.solaris NNTP-Posting-Host: 63.204.7.5 NNTP-Posting-Date: Mon, 08 Jan 2007 18:23:35 EST References: <1168279498.634359.194800@38g2000cwa.googlegroups.com> <20070108133159.166e2850@oscar-sled.home.lan> <1168285352.423286.291970@51g2000cwl.googlegroups.com> <1168288960.255820.234320@q40g2000cwq.googlegroups.com> Message-ID: Date: Mon, 08 Jan 2007 23:23:35 GMT From: Darren Dunham Subject: Re: Sunfire v210 serial console... configuration forrie@gmail.com wrote: > > Hey Gary, long time no see. > > I just tried hooking up the RJ45 to the Serial *and* Net Mgmt ports, > with no luck. I'm pretty sure the COMMs parameters on the Wyse are > correct. Do you have a null modem connector in there? Both a PC running netcom and a physical terminal are wired DTE, same as the sun. It'll require a null modem. Even if the "console" wasn't working, you should still be able to communicate with the LOM. The 'Net Mgmt' port is Ethernet, not serial. > If I remember correctly, the SAF is responsible for spawning the getty > on the port... in the inittab, I only see this: That is incorrect. SAC/SAF stuff is usually used for additional gettys on serial ports, not for the console. > co:234:respawn:/usr/lib/saf/ttymon -g -h -p "`uname -n` console login: > " -T vt100 -d /dev/console -l console -m ldterm,ttcompat Right. That's the console invocation. > /dev/console points to: > crw--w---- 1 root tty 0, 0 Jan 8 15:40 > /devices/pseudo/cn@0:console Which is a device managed by the OBP. It can direct that where it wants, but on LOM hardware, it probably goes to the LOM. > I have some serial cables here, but they aren't marked null-modem, > so perhaps those won't work with a system-to-system (via minicom) > connection. That would be my first guess. > Are there other settings I can poll to see what the console is set to, > etc. It's unlikely to be set to anything other than 9600 8/N/1. I don't know how to poll LOM settings from the host. Here's the ALOM doc. http://www.sun.com/products-n-solutions/hardware/docs/pdf/819-2445-11.pdf Also the v210 admin guide, with sections 1.4 and 3.4 showing how you command the OS from the ALOM port. http://www.sun.com/products-n-solutions/hardware/docs/pdf/819-4208-10.pdf -- Darren Dunham ddunham@taos.com Senior Technical Consultant TAOS http://www.taos.com/ Got some Dr Pepper? San Francisco, CA bay area < This line left intentionally blank to confuse you. > ////////////////////////////////////////////////////////////////////////////// Newsgroups: comp.unix.solaris References: <1307hmckkhvsre8@corp.supernews.com> Message-ID: <130bcrp92a4rf0a@corp.supernews.com> Date: Sun, 25 Mar 2007 09:25:44 +1000 From: pp Subject: Re: Serial cable on Sun Netra Frank Cusack wrote: > > On Fri, 23 Mar 2007 23:23:38 +1100 pp wrote: > >> I have a SUN NETRA T1 105 UltraSPARC-IIi 440MHz 1U Server, but missing >> a serial cable for two serial ports. >> >> Can anyone tell me what serial cable compatible with the two serial >> ports for this server? > > http://www.sun.com/products-n-solutions/hardware/docs/pdf/806-4707-10.pdf > has the pinout, and general information about the serial ports. > > > > http://www.sun.com/products-n-solutions/hardware/docs/Servers/Netra_Servers/netra_t1_105/index.html> > > has links to other T1 documentation. > > What serial cable you would use depends on what you will have on the > other end. If you have a terminal server with RJ-45 ports, most > likely you can use the sun/cisco adapter from Cyclades (now Avocent), > or a cisco rollover cable. > > I prefer the adapter; then all cables in my rack are the same cat 5e/6 > straight-through cables. It's easier to change lengths of a standard > cable than to have to get a new specialized cable. > > If you want to attach a modem or other 9- or 25-pin device, it's easiest > to make up an adapter yourself, using the rj45->serial adapters commonly > available, which allow you to configure the pins however you like. They > cost a dollar or thereabouts. > > -frank Hi, I am not too sure which one. I don't want to spend time to make one as it is very cheap in the market. I found the following item may be the one I am looking for? http://cgi.ebay.com/Cisco-Console-Cable-RJ45-to-DB9-Brand-New-Free-post_W0QQitemZ220093533089QQcategoryZ11185QQssPageNameZWDVWQQrdZ1QQcmdZViewItem Thanks P ////////////////////////////////////////////////////////////////////////////// Newsgroups: comp.sys.sun.hardware NNTP-Posting-Host: 66.160.54.164 NNTP-Posting-Date: Sat, 26 Jan 2008 14:07:16 -0600 References: <5vu08kF1nco4sU1@mid.individual.net> Message-ID: <_v-dnaZ0cshpDwbanZ2dnUVZ_s2tnZ2d@cavtel.net> Date: Sat, 26 Jan 2008 15:08:00 -0500 From: Trinean Subject: Re: Connecting to Sun StorEdge 3310 "Ste" wrote in message news:5vu08kF1nco4sU1@mid.individual.net... > Hello all, > > in our warehouse I've found a Sun StorEdge 3310. I want to try to use it > but I do not have any kind of usefull serial cable. Also StorEdge has a > LAN port but I'm not able to find a mac address to force ARP table and > telnet it. > > Any hint to get my storage accessible? > > Thanks > Stefano You need a DB9 NULL modem cable, male on the side for the SE3310. Depending on what you're going to tip onto it from will determine if any additional adapters are needed for the other end. I believe the data rate for these are often set high at 38400 bps, instead of the standard Sun 9600. Trinean ////////////////////////////////////////////////////////////////////////////// Newsgroups: comp.unix.solaris References: Message-ID: Organization: http://www.andreas-borchert.de/ Date: Sat, 26 Apr 2008 17:52:39 +0200 (CEST) From: Andreas F. Borchert Subject: Re: Sun Storedge 3310 On 2008-04-25, Miroslav Zubcic wrote: > > It has also network connectivity (2 ports) and 2 serial rs232 ports, but > I was either too drunk to configure them, or they were broken, or network > stuff screwed up VLANs first day, so the next day I just downloaded and > used sccli SCSI-oriented command (which can be found someware on > sun.com) to creat 2 RAID 1+0 configs. The 3310 uses DHCP to gets its address over the network. Just have a DHCP server operating and then you can telnet to that device to have console access. The RS 232 port expects a speed of 38400 (a bit unusual in a Sun environment). You can use that alternatively or at least to configure its network connection if you do not want to do this through DHCP. There are some operations that require console access (either via the network or the serial line) as the in-band connection works only as long you have at least one SCSI device configured. -- Andreas. ////////////////////////////////////////////////////////////////////////////// Newsgroups: comp.unix.solaris NNTP-Posting-Host: 68.37.156.84 NNTP-Posting-Date: Sun, 15 Nov 2009 03:17:09 +0000 (UTC) Message-ID: <277b439c-1f4d-4d1d-a786-019c6d7710bb@w19g2000yqk.googlegroups.com> Date: Sat, 14 Nov 2009 19:17:08 -0800 (PST) From: xerces Subject: serial port connectivity set-up Hi All, I am trying to get a serial port connection going between a Sun M3000 server and an external PC so as to be able to deploy an electronic real-time data feed from the PC to the Sun server. I believe the cabling is OK The console port on the sun m3000 is RJ45 and an appropriate converter is in use along with the null modem cable, so I am told. At the application level on the Solaris 10 server (Sun M3000 server), I am trying to open and reference "some" serial port and receive the data feed but have not had success. I am trying to open a port like /dev/ttya but this is failing. I have: % ls -ltr /dev/ttya lrwxrwxrwx 1 root root 6 Apr 23 2009 /dev/ttya -> term/a 11Nov--Wed 4:49:43pm t3edbo@SUNSRV02(/asp_APPL/t3e231/server)% ls -ltr /dev/term/a lrwxrwxrwx 1 root root 50 Apr 23 2009 /dev/term/a -> ../../devices/pci@8,4000/ebus@1/serial@14,400000:a 11Nov--Wed 4:49:49pm t3edbo@SUNSRV02(/asp_APPL/t3e231/server)% ls -ltr /dev/tty lrwxrwxrwx 1 root root 26 Apr 23 2009 /dev/tty -> ../devices/pseudo/sy@0:tty I realize some information is fuzzy, but what do I need to do to get the set-up and working ? What else can I check ? What can I check to ensure cabling is ok ? What should it be ? Can someone please help and point me in the right direction. Also pasted below is my /etc/remote file: # The next 17 lines are for the PCMCIA serial/modem cards. # pc0:\ :dv=/dev/cua/pc0:br#38400:el=^C^S^Q^U^D:ie=%$:oe=^D:nt:hf: pc1:\ :dv=/dev/cua/pc1:br#38400:el=^C^S^Q^U^D:ie=%$:oe=^D:nt:hf: pc2:\ :dv=/dev/cua/pc2:br#38400:el=^C^S^Q^U^D:ie=%$:oe=^D:nt:hf: pc3:\ :dv=/dev/cua/pc3:br#38400:el=^C^S^Q^U^D:ie=%$:oe=^D:nt:hf: pc4:\ :dv=/dev/cua/pc4:br#38400:el=^C^S^Q^U^D:ie=%$:oe=^D:nt:hf: pc5:\ :dv=/dev/cua/pc5:br#38400:el=^C^S^Q^U^D:ie=%$:oe=^D:nt:hf: pc6:\ :dv=/dev/cua/pc6:br#38400:el=^C^S^Q^U^D:ie=%$:oe=^D:nt:hf: pc7:\ :dv=/dev/cua/pc7:br#38400:el=^C^S^Q^U^D:ie=%$:oe=^D:nt:hf: cuab:dv=/dev/cua/b:br#2400 dialup1|Dial-up system:\ :pn=2015551212:tc=UNIX-2400: hardwire:\ :dv=/dev/term/b:br#9600:el=^C^S^Q^U^D:ie=%$:oe=^D: tip300:tc=UNIX-300: tip1200:tc=UNIX-1200: tip0|tip2400:tc=UNIX-2400: tip9600:tc=UNIX-9600: tip19200:tc=UNIX-19200: UNIX-300:\ :el=^D^U^C^S^Q^O@:du:at=hayes:ie=#$%:oe=^D:br#300:tc=dialers: UNIX-1200:\ :el=^D^U^C^S^Q^O@:du:at=hayes:ie=#$%:oe=^D:br#1200:tc=dialers: UNIX-2400:\ :el=^D^U^C^S^Q^O@:du:at=hayes:ie=#$%:oe=^D:br#2400:tc=dialers: UNIX-9600:\ :el=^D^U^C^S^Q^O@:du:at=hayes:ie=#$%:oe=^D:br#9600:tc=dialers: UNIX-19200:\ :el=^D^U^C^S^Q^O@:du:at=hayes:ie=#$ %:oe=^D:br#19200:tc=dialers: VMS-300|TOPS20-300:\ :el=^Z^U^C^S^Q^O:du:at=hayes:ie=$@:oe=^Z:br#300:tc=dialers: VMS-1200|TOPS20-1200:\ :el=^Z^U^C^S^Q^O:du:at=hayes:ie=$@:oe=^Z:br#1200:tc=dialers: dialers:\ :dv=/dev/cua/b: -------------------------------------------------------------------- The attributes are: dv device to use for the tty el EOL marks (default is NULL) du make a call flag (dial up) pn phone numbers (@ =>'s search phones file; possibly taken from PHONES environment variable) at ACU type ie input EOF marks (default is NULL) oe output EOF string (default is NULL) cu call unit (default is dv) br baud rate (defaults to 300) fs frame size (default is BUFSIZ) -- used in buffering writes on receive operations tc to continue a capability Thanks very much . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Newsgroups: comp.unix.solaris References: <277b439c-1f4d-4d1d-a786-019c6d7710bb@w19g2000yqk.googlegroups.com> Message-ID: <7mb101F3hj4llU1@mid.individual.net> Date: Sun, 15 Nov 2009 19:51:01 +0100 From: Michael Laajanen Subject: Re: serial port connectivity set-up Hi, xerces wrote: > > Hi All, > > I am trying to get a serial port connection going between a Sun M3000 > server and an external PC... Start with a loopback cable TX <--> RX. Does the M3000 have a port B? If so then try $ tip hardwire (followed by "hello") and check if it echoes. Then remove the jumper and check again and now it should not echo. I you need to use port A, change hardwire to use A. You might have problems with A since possible the login process is using it for serial login!! Then you must disable the login process (getty) /michael If you use tip hardwire... //////////////////////////////////////////////////////////////////////////////